Quick verdict
The S37 is Liberty's lower-cost route into a 1/3 HP pump with an oil-filled motor and a vortex impeller. It is a sensible replacement for a tired builder-grade pump in an ordinary pit. Liberty publishes less about it than about the 250-Series: the curve is a graphic and no switch levels are printed, so buyers who size closely should look at a better-documented model.
Who it fits, and who should skip it
A good fit if
- You are replacing a 1/3 HP pump on an existing 1-1/2 in line.
- Your pit is at least 14 in across and the float has room to travel.
- You may later add Liberty's StormCell battery backup as a matched combo.
Look elsewhere if
- You need a printed flow-at-height table to size against a tall lift.
- Your pit is only 10 in wide; Liberty's VMF models fit there.
Specifications
Motor
| Horsepower | 1/3 HP |
|---|---|
| Voltage | 115 V, 60 Hz |
| Amps | 6.5 A (brochure); 6.2 A in the PC442 combo table |
| Motor type | Oil-filled, thermal overload protection, dual bearings |
Figures: Liberty Pumps sump pump brochure (S30-Series and model selection table); Liberty Pumps PC442-Series sales literature LLIT006747.
Performance
| Max flow | 45 GPM (listing figure) |
|---|---|
| Max head | Not stated on the data sheet; S30 curve is printed only as a graphic |
Figures: Amazon listing B002YSAW18; Liberty Pumps sump pump brochure (S30-Series and model selection table).
Switch
| Switch type | Vertical float switch |
|---|---|
| On / off levels | Not stated on the data sheet |
Figures: Liberty Pumps sump pump brochure (S30-Series and model selection table).
Build
| Discharge | 1-1/2 in |
|---|---|
| Construction | Poly and cast iron |
| Impeller | Vortex style, with raised inlet ports |
| Minimum pit | 14 in diameter |
| Weight | 14 lb (listing) |
| Warranty | 3 years on Liberty wholesale products; the listing quotes 2 years |
Figures: Liberty Pumps sump pump brochure (S30-Series and model selection table); Liberty Pumps PC442-Series sales literature LLIT006747; Amazon listing B002YSAW18; Liberty Pumps wholesale warranty.
Versions
The S30-Series comes in three switch versions, and the S37 is also sold as the primary pump in factory-assembled battery backup combos.
| Version | Part number | What differs | Listing |
|---|---|---|---|
| S37, vertical float | S37 | 1/3 HP, 115 V, 1-1/2 in discharge | View on Amazon |
| S37-P, vertical float with piggyback plug | S37-P | Same pump; switch plugs in series so the pump can run manually | Not linked |
| S38, wide-angle float | S38 | Wide-angle float with piggyback plug, 14 in pit | Not linked |
| S37 with 442 backup | PCS37-442-10A | Assembled combo with 12 V DC backup pump and 10A charger, 33 lb | Not linked |
| S37 with 442 backup and Wi-Fi | PCS37-442-10A-EYE | As above, wireless enabled | Not linked |
Figures: Liberty Pumps sump pump brochure (S30-Series and model selection table); Liberty Pumps PC442-Series sales literature LLIT006747.
Installation and setup
The S37 drops into a pit at least 14 in in diameter, the figure Liberty gives for the whole S30-Series. That width leaves the vertical float room to rise and fall beside the motor without catching on the liner. Set the pump on a firm, level floor in the basin and pipe the 1-1/2 in discharge at full size; reducing the line, under Liberty's warranty terms, is one of the conditions that voids coverage.
Liberty's warranty also excludes water containing sand, lime, cement or gravel, so clear any construction debris from a new pit before start-up. Fit a check valve and a union above the basin lid for easy removal, and plug the cord into its own grounded outlet. If you choose the S37-P, the switch's piggyback plug goes into the wall and the pump plugs into its back, which lets you bypass the float to run the pump by hand.
Switch and sizing notes
A vertical float rides up and down a short guide beside the pump, which keeps it compact compared with a tethered float that swings in an arc. Liberty does not print start and stop heights for the S37, so expect to watch the first few cycles and make sure the pit is deep enough that the pump stays covered at the off point.
Sizing is where this model is thin on data. Liberty plots the S30 curve on its brochure performance chart, but only as a graphic, and the retail listing gives a single 45 GPM top figure. If your discharge climbs more than about one storey, or your pit fills quickly in storms, compare a model with a printed curve; the sizing calculator will show the total head you need to beat, and Liberty 257 vs 237 covers two better-documented 1/3 HP siblings.
Ownership and maintenance
Liberty lists oil-filled motors with thermal overload protection, a dual bearing design and higher inlet ports that keep debris away from the impeller, all features that reduce routine attention. A quick test every few months, filling the pit until the float lifts, is still the best way to catch a sticking switch before a storm does.
Warranty wording differs by source. Liberty's wholesale warranty page sets three years from purchase, with a dated receipt showing model and serial number, while the retail listing quotes two years. Keep the receipt, and ask the seller which term applies to your unit.
Pros and cons
Pros
- Oil-filled motor with thermal protection.
- Vortex impeller and raised inlet ports.
- Fits a 14 in pit with a compact float.
- Ready-made combo versions with battery backup.
Cons
- No printed flow-at-height figures.
- Switch levels are not published.
- Warranty term differs between sources.
Alternatives worth comparing



Final verdict
Buy the S37 as a straightforward 1/3 HP replacement for an average pit, or as the primary in a Liberty combo. If you need firm flow figures or switch heights to size a demanding pit, Liberty's 250-Series or a fully documented rival is the safer pick.
Where to buy
Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure
Questions buyers ask
What does S37 mean in Liberty's range?
The S37 belongs to Liberty's S30-Series, the brand's competitively priced 1/3 HP line. The retail listing calls it a Builders Series pump. It shares the series motor and body with the S37-P and S38, which differ only in their switch arrangement.
Is the Liberty S37 cast iron?
Liberty describes its construction as poly and cast iron, not all cast iron. One retail listing row calls the material stainless steel, which does not match the maker. If an all-iron body matters to you, the Liberty 257 is the cast iron 1/3 HP choice.
Can the S37 be part of a battery backup system?
Yes. Liberty sells the PCS37-442-10A, a factory-assembled combo that pairs the S37 with its 442 12 V DC backup pump, a 10A charger and controller, and both check valves. Those systems need a pit at least 18 in across and 18 in deep.
How much water can the S37 pump?
The retail listing gives 45 GPM as the top flow. Liberty shows the S30 curve only as a chart graphic, without a printed table, so flow at your exact lift is not stated in text. For a tall discharge run, choose a model with published figures.
