Quick verdict
The 92330 is a light, low-draw pump for a pit that sees modest water: a spare, a crawl space basin or a home where the old pump simply wore out. It handles small grit poorly, with a 1/8 in solids limit, and its 1-year warranty is shorter than Superior's cast iron range. Plan for replacement rather than decades of service.
Who it fits, and who should skip it
A good fit if
- Your inflow is light and the lift is about 10 ft or less.
- You want a pump light enough to lift out of the pit one-handed.
- You need a spare that can double as a manual utility pump.
Look elsewhere if
- Your sump water carries sand or grit beyond 1/8 in particles.
- You want a multi-year warranty; this one is covered for one year.
Specifications
Motor
| Horsepower | 1/3 HP |
|---|---|
| Voltage | 120 V, 60 Hz, 15 A circuit |
| Amps | 4.1 A |
| Motor type | Continuous duty, capacitor start, thermally protected |
Figures: Superior Pump submersible sump pump owner's manual, revised 10-08.
Performance
| Max flow | 40 GPM at 0 ft |
|---|---|
| Flow at 5 ft | 34 GPM |
| Flow at 10 ft | 28 GPM |
| Flow at 15 ft | 22 GPM |
| Flow at 20 ft | 12 GPM |
| Max head | 25 ft (2 GPM at that height) |
Figures: Superior Pump submersible sump pump owner's manual, revised 10-08; Amazon listing B000IJR5GK.
Switch
| Switch type | Tethered float with piggyback plug |
|---|---|
| On / off levels | Not stated on the data sheet |
Figures: Amazon listing B000IJR5GK; Superior Pump submersible sump pump owner's manual, revised 10-08.
Build
| Discharge | 1-1/4 in (listing: 1-1/4 or 1-1/2 in NPT) |
|---|---|
| Solids handling | 1/8 in |
| Construction | Thermoplastic |
| Liquid temperature | 32 °F to 120 °F (0 °C to 49 °C) |
| Power cord | 10 ft |
| Weight | 8.95 lb (listing) |
| Minimum basin | 14 in diameter |
| Warranty | 1 year |
Figures: Superior Pump submersible sump pump owner's manual, revised 10-08; Amazon listing B000IJR5GK.
Installation and setup
Superior's sump manual covers sixteen sump models, and the 92330 shares its performance row with the 92335 and 92342. Its installation advice is plain. Disconnect power, pull the old pump and its piping, and clean the basin before the new one goes in. Stand the pump on a solid footing, off to one side, never on bare ground, sand or rocks. The basin should be at least 14 in across so the tethered float can swing from bottom to top without brushing the wall, which is the most common cause of a stuck switch.
A grounded 120 V outlet should be within 6 ft of the pit, ideally a GFCI. Superior prefers a direct connection; if an extension is unavoidable, it must be a grounded waterproof cord no longer than 25 ft and no lighter than 14/3 gauge. Add a full-flow swing check valve of the same size as the outlet, as close to the pump as possible, then schedule 40 PVC. Corrugated drain hose is meant for temporary jobs only.
Switch and sizing notes
The float hangs on its own cord and plugs into the wall with the pump cord plugged into its back, the usual piggyback arrangement. Test it before closing the lid: with the pit empty the pump should stay silent; pour in water with a bucket or hose until the float tips up and the pump starts, then watch it shut off. Superior does not publish fixed start and stop heights, because they depend on how long you leave the tether.
On the curve, Superior lists 34 GPM at 5 ft, 28 GPM at 10 ft and 22 GPM at 15 ft, then 12 GPM at 20 ft. That makes it a short-lift pump. Use the sizing calculator to add your pipe run to the vertical rise, and if inflow outpaces these numbers, look at the 1/3 HP shortlist for cast iron options.
Ownership and maintenance
The listing notes the pump can also run as a utility pump, taking water down to about 1/2 in from the floor when used that way. Keep it in clear water: the manual forbids sewage, chemicals and liquids above 120 °F, and warns that the thermal overload, which shuts the motor down when it overheats, is a safety device that wears out with repeated trips. Never run it dry.
If it starts and stops too often, look at the check valve first. If it runs without moving water, check the intake screen, a frozen line or the airlock hole, which a paper clip clears. Superior's warranty on this model is one year from purchase.
Pros and cons
Pros
- Modest 4.1 A running draw on a 120 V circuit.
- Light enough for easy removal.
- Doubles as a manual utility pump.
- Simple piggyback float to test or replace.
Cons
- Small 1/8 in solids limit.
- Warranty runs for one year only.
- Flow is modest above 15 ft.
Alternatives worth comparing



Final verdict
Buy the 92330 as an affordable spare or for a light-duty pit with a short lift. For a main basement pump facing heavy inflow or gritty water, a cast iron model with a longer warranty is the stronger long-term choice.
Where to buy
Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure
Questions buyers ask
How much water does the Superior 92330 move?
Superior lists 40 GPM with no lift, which is the 2,400 GPH quoted on the listing. Flow at a real basement lift is lower: 28 GPM at 10 ft and 22 GPM at 15 ft. Base your choice on those figures rather than the headline number.
Is the 92330 the same as the 92341?
No. Both are 1/3 HP Superior sump pumps in the same manual, but the 92341 handles 3/8 in solids, has a 1-1/2 in outlet, a stronger curve and a three-year warranty. The 92330 is the lighter, simpler pump with a 1-1/4 in outlet.
What size pipe should I use with the 92330?
The manual lists a 1-1/4 in discharge, and the listing says the pump connects to 1-1/4 or 1-1/2 in NPT. Superior advises pipe the same size as the outlet or larger, since a smaller pipe will not hurt the pump but reduces output.
Can I use the 92330 to empty a flooded floor?
Yes, as a stopgap. Plugged in without the float, it runs as a manual utility pump and, per the listing, takes water down to about 1/2 in. Stay with it while it runs, since running dry damages the motor.
