Comparison ยท Sump pumps

Zoeller M57 vs Zoeller M98

Two cast iron Zoeller sump pumps with built-in floats. The real choice is the M57's all-iron build and lower start level against the M98's much stronger curve.

By Pumpendium Editorial · Updated November 2026

Zoeller M57 Mighty-Mate

Zoeller M57 Mighty-Mate Sump Pump

All cast iron 3/10 HP sump pump with a cast iron vortex impeller.

Check price on Amazon
vs
Quick verdict

Choose the Zoeller M57 when the lift is short, the pit is shallow and you want iron down to the impeller, since it starts at a lower water level and needs less height.

Choose the Zoeller M98 when the discharge climbs past about 12 ft, the pit floods quickly or the line is long, because its 1/2 HP motor keeps pumping where the M57 has already stopped.

Key specifications

SpecificationZoeller M57 Mighty-Mate Sump PumpZoeller M98 Flow-Mate Sump Pump
Horsepower3/10 HP1/2 HP
MotorShaded pole, 1550 RPM, sleeve bearingsPermanent split capacitor, 1725 RPM, oil-fed cast iron bearings
Amps at 115 V9.7 A9.4 A
Flow at 5 ft (maximum)43 GPM72 GPM
Flow at 10 ft34 GPM61 GPM
Flow at 15 ft19 GPM45 GPM
Flow at 20 ftNone (shut-off at 19.25 ft)25 GPM
Shut-off head19.25 ft23 ft
Switch levels (automatic model)On 7-1/4 in, off 3 inOn 9-1/2 in, off 3 in
ImpellerCast iron, non-clogging vortexThermoplastic or cast iron vortex (engineered plastic on the sales sheet)
BodyAll cast iron, including the baseCast iron cap, motor and pump housing; thermoplastic or cast iron base
Discharge and solids1-1/2 in NPT, 1/2 in spherical solids1-1/2 in NPT, 1/2 in spherical solids
Weight29 lb36 lb
Warranty3-year limited3-year limited

Figures: Zoeller technical data sheet FM2778, Mighty-Mate series (Models 53, 55, 57, 59); Zoeller technical data sheet FM2779, Flow-Mate Model 98; Zoeller Model 98 sales sheet FM3012; Zoeller installation instructions and 3-year warranty FM2676; Zoeller Model 98 product page.

Scorecard

CriterionEdgeWhy
Water moved at a 15 ft liftZoeller M98 Flow-Mate Sump PumpZoeller's tables give 45 GPM for the M98 at 15 ft and 19 GPM for the M57, well over double.
Reach on a tall dischargeZoeller M98 Flow-Mate Sump PumpThe M98 still delivers 25 GPM at 20 ft, a height the M57 cannot reach at all.
Start level in a shallow pitZoeller M57 Mighty-Mate Sump PumpThe M57 switches on at 7-1/4 in of water, more than two inches below the M98's start point.
Iron throughoutZoeller M57 Mighty-Mate Sump PumpZoeller lists the M57 as all cast iron with an iron impeller; the M98 normally ships with plastic parts below the housing.
Warranty and fittingsEvenBoth carry Zoeller's three-year limited warranty and share the same discharge size and solids rating.

How far apart the curves really are

On paper the gap is 3/10 HP against 1/2 HP. In the pit it is bigger than that sounds. Zoeller's own tables put the M57 at 43 GPM with a 5 ft lift, 34 GPM at 10 ft and 19 GPM at 15 ft, with shut-off just past 19 ft. The M98 starts at 72 GPM and still moves 61 GPM at 10 ft, 45 GPM at 15 ft and 25 GPM at 20 ft before stopping at 23 ft.

For a basement where the pipe rises eight or nine feet and exits through the rim joist, the M57 has enough capacity for steady seepage. Once friction from a long run or several elbows pushes total head toward 15 ft, its output falls off quickly, and that is where the M98 earns its larger motor. Work out your total head with the sizing calculator before deciding.

All-iron build against an iron shell

The M57 is the iron member of the Mighty-Mate family. Zoeller's data sheet describes the M57 as all cast iron construction with a cast iron impeller, where the better-known M53 uses a plastic impeller and base. That makes the M57 a little heavier for its size, at 29 lb, and means the parts that meet grit at the intake are metal rather than plastic. It is an old design that many plumbers already know from service calls, and replacement parts are listed for it.

The M98 puts its iron where the heat is. The cap, motor housing and pump housing are cast iron, and the bearings are oil-fed cast iron, but the tech sheet lists the base and impeller as thermoplastic or cast iron and the sales sheet names an engineered plastic impeller. For clean groundwater that is not a weakness. For a pit that collects sand, the M57's metal impeller is the more forgiving part.

Two different motors

The M57 runs a shaded pole motor at 1550 RPM on sleeve bearings, the simple design Zoeller has used on its smaller pumps for decades. The M98 uses a permanent split capacitor motor at 1725 RPM on oil-fed cast iron bearings. Both are oil filled and both have an automatic reset thermal overload.

A curious detail in the model charts: the M57 lists 9.7 A at 115 V and the M98 lists 9.4 A, so the larger pump draws slightly less current on its nameplate. Either one belongs on its own circuit, and neither should share an outlet with a freezer or a dehumidifier that could trip the breaker during a storm. Our guide to sump pump amps and power use covers circuit sizing.

Switch levels and pit depth

Both automatic models use an integral float-operated mechanical switch, so no separate float hangs in the pit. The difference is where it trips. The M57 starts at 7-1/4 in of water and stops at 3 in. The M98 waits until 9-1/2 in and also stops at 3 in, which moves more water per cycle and means fewer starts on a wet day.

The taller start level and taller body matter in a shallow or shared pit. The M98 stands 12-1/16 in high against about 10 in for the M57 body, and a pit with a high inlet pipe may flood the drain tile before the M98 switches on. Measure from the pit floor to the lowest inlet before choosing. Our basin cycle calculator shows how the drawdown affects run frequency.

Versions, cords and upkeep

Each pump comes in the same set of versions. Zoeller lists the M model as automatic at 115 V, the D model as the automatic version for a 230 V circuit, and the N and E models as nonautomatic for use with an external switch or panel. Piggyback variable-level versions are sold as BN57 and BN98. Automatic units have a 9 ft cord and nonautomatic units a 15 ft cord.

Care is identical. Zoeller asks for a relief hole of about 3/16 in in the discharge pipe below the check valve, even though both pump housings already carry a vent, and for a regular look at the float for debris. The 98-0001 automatic model also comes with Zoeller's LED plug, which glows when the outlet is live.

Who each one fits

The Zoeller M57 Mighty-Mate Sump Pump fits if

  • The discharge rises no more than about 10 ft in total.
  • Your pit is shallow and the inlet pipe sits low.
  • Sand or grit reaches the pit and a metal impeller appeals.
  • You are replacing an older M57 and want the same footprint.

Full reference

The Zoeller M98 Flow-Mate Sump Pump fits if

  • Total head is 12 ft or more once pipe friction is counted.
  • Heavy rain fills the pit faster than a small pump can clear it.
  • You prefer a PSC motor on oil-fed bearings.
  • You want a visible power check from the LED plug.
  • The pit is deep enough for a 9-1/2 in start level.

Full reference

Questions readers ask

Is the Zoeller M98 just a bigger M57?

No. They belong to different series. The M57 is a 3/10 HP Mighty-Mate with a shaded pole motor and an all cast iron body, while the M98 is a 1/2 HP Flow-Mate with a permanent split capacitor motor, a taller housing and a much stronger performance curve.

Can an M98 replace an M57 in the same pit?

Usually, since both use a 1-1/2 in NPT discharge. Check that the pit has room for the taller M98 body and that its 9-1/2 in start level sits below the inlet pipe, otherwise water may back up into the drain tile before the pump starts.

Which one lasts longer?

Zoeller backs both with the same three-year limited warranty and gives no life rating for either. The M57 has the more robust impeller material, while the M98 has the better bearings. A clear pit, a working check valve and a vent hole matter more than the model for service life.

Do the M57 and M98 handle the same solids?

Yes. Both use a non-clogging vortex impeller that passes 1/2 in spherical solids, which is plenty for groundwater with some silt. Neither is meant for sewage, and Zoeller says not to use dewatering pumps in pits that handle raw waste.

Final verdict

This pairing comes down to lift and pit. The M57 is a compact, all-iron pump for short, gentle discharge runs in a shallow pit, and it starts sooner as water rises. The M98 trades some of that iron for a larger motor that keeps real flow at 15 and 20 ft. Measure your total head first; if it is near or above 15 ft, the M57 is simply too small.

How we research · Disclosure