Shallow well jet ยท Flotec

Flotec FP4022 Shallow Well Jet Pump

The FP4022 is Flotec's 3/4 HP shallow well jet with a fiberglass-reinforced thermoplastic body. The listing rates it at up to 12 GPM at 40 psi for water 25 ft or less below the pump.

Model FP4022 · part number FP4022-10 · Updated November 2026

Horsepower
3/4 HP
Voltage
115/230 V; ready to install at 230 V
Max flow
Up to 12 GPM at 40 psi
Max head
Not stated on the data sheet
Switch type
Pressure switch preset to 30/50 psi

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Quick verdict

In short

This is the non-rusting alternative to Flotec's cast iron FP4122. The thermoplastic housing will not corrode, which suits damp pump pits and acidic water, and the pump weighs far less. It gives up some output: the listing tops out at 12 GPM at 40 psi, against 14.7 GPM for the cast iron model.

Who it fits, and who should skip it

A good fit if

  • Damp pump houses where cast iron would rust.
  • Shallow wells, points or lakes within 25 ft.
  • Owners who want a lighter pump to lift into place.

Look elsewhere if

  • Water more than 25 ft below the pump.
  • Buyers who want a published flow table at each lift.

Specifications

Motor

Horsepower3/4 HP
Voltage115/230 V; ready to install at 230 V
Amps6.1 A at 230 V, 12.2 A at 115 V

Figures: Amazon listing B0002YWTM6 (Flotec FP4022-10); Pentair shallow well pumps installation manual P15002.

Performance

Max flowUp to 12 GPM at 40 psi
Max headNot stated on the data sheet
Maximum lift25 ft depth to water or less

Figures: Amazon listing B0002YWTM6 (Flotec FP4022-10).

Controls

Switch typePressure switch preset to 30/50 psi

Figures: Amazon listing B0002YWTM6 (Flotec FP4022-10).

Connections

Suction1-1/4 in
Discharge1 in

Figures: Amazon listing B0002YWTM6 (Flotec FP4022-10).

Build

HousingFiberglass-reinforced thermoplastic
Item weight26.2 lb (listing)
Key partsMotor J218-1652, impeller J105-42PNB, shaft seal U109-6B
Diffuser and nozzleAssembly N101-30P; pump body N76-46P
Manufacturer part number6968069 (listing)

Figures: Amazon listing B0002YWTM6 (Flotec FP4022-10); Pentair shallow well pumps installation manual P15002.

Versions

Pentair's manual lists the FP4022-10 alongside 1/2 HP and 1 HP thermoplastic siblings that share many parts.

VersionPart numberWhat differsListing
FP4022-10, 3/4 HPFP4022-10Thermoplastic shallow well jet, 30/50 switchView on Amazon
FP4012-10, 1/2 HPFP4012-10Same body family; motor J218-1651-115Not linked
FP4032-10, 1 HPFP4032-10Same body family; motor J218-1653Not linked

Figures: Pentair shallow well pumps installation manual P15002.

Installation and setup

Pentair's shallow-well manual, which lists the FP4022-10 in its parts index, starts with placement: as close to the water as possible, with the fewest fittings and a suction pipe no smaller than the pump's inlet. Support the pipe so it rises gently toward the pump without dips; a high spot can trap enough air to stop the jet.

In a cased well, hang a free-moving foot valve and strainer about 5 ft above the bottom and at least 10 ft below the pumping water level. For a lake or pond, screen the foot valve against fish and debris. A driven point needs a check valve instead. Seal every suction joint with PTFE tape, because the pump cannot lift water through a line that leaks air.

The listing describes the motor as ready to install at 230 V, with 115 V conversion covered in the manual. Fit a relief valve rated for full flow at 75 psi.

Switch and sizing notes

The switch is preset to 30/50 psi; set a precharged tank 2 psi below cut-in. A pressure gauge on the pump makes it easy to watch the switch work. Our switch settings guide explains the common bands.

Flotec's listing gives a single headline, up to 12 GPM at 40 psi, and notes that average household use runs well below that. Without a lift-by-lift table, assume output falls as the water gets deeper and keep this pump for sources comfortably inside 25 ft. If you want published figures at each lift, the cast iron FP4122 has them.

Ownership and maintenance

Fill the pump and every suction pipe through the priming tee before starting, then refill and retry if water does not come within a few minutes; a 25 ft lift can need a long priming session. The housing is self-priming only after that first fill.

Because the unit is serviceable, Pentair publishes its parts by number: seal, impeller, diffuser and motor. A worn seal or impeller is a bench repair rather than a reason to replace the pump.

Pros and cons

Pros

  • Thermoplastic housing that cannot rust.
  • Preset 30/50 switch, 230 V ready.
  • Repair parts listed by Pentair part number.
  • Lighter than cast iron jets.

Cons

  • Only a single flow figure published.
  • Less flow than the cast iron FP4122.
  • Limited to 25 ft of lift.

Alternatives worth comparing

Final verdict

The FP4022 makes sense where corrosion is the enemy and the water is shallow. If you want the most flow and a detailed curve, the cast iron FP4122 is the stronger Flotec option.

Where to buy

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Questions buyers ask

Is the Flotec FP4022 plastic or cast iron?

Its pump housing is fiberglass-reinforced thermoplastic, which the listing promotes for corrosion resistance. Flotec's cast iron 3/4 HP shallow jet is the FP4122. Both are shallow well pumps for water within 25 ft.

How much water does the FP4022 deliver?

The listing quotes up to 12 GPM at 40 psi and says average household use is lower. Flotec does not publish a lift-by-lift table for this model in the documents saved here, so expect less as lift increases.

Does it need a foot valve?

Yes, or a check valve. The pump is self-priming only once its housing is filled, and Pentair's manual calls for a foot valve on cased wells and surface water, or a check valve on a driven point.

Can it run on 115 V?

Yes. It ships ready for 230 V, drawing 6.1 A, and the manual covers conversion to 115 V, where it draws 12.2 A. Size the breaker and wire for the voltage you choose.