When a toilet, shower or laundry sits below the main sewer line, waste collects in a sealed, vented basin and a sewage ejector lifts it up to the drain. Unlike a sump pump, an ejector must pass solid waste, so codes typically call for 2 in solids handling and a 2 in discharge, both of which every pick here offers.
Three picks are pumps for an existing basin and two are complete systems with basin, cover and pump. Every one has a cast iron pump body. If you are deciding between pump types, read sewage ejector vs grinder vs sump pump, and for the install itself see upflush and macerating options if a basin is not possible.
- Qualifies if
- Passes 2 in spherical solids.
- A 2 in discharge connection.
- Cast iron pump or motor housing.
- Maker publishes flow at a lift and a warranty.
- On the list
- 5 pumps
The picks
Zoeller M267 Waste-Mate Sewage Pump
Best for: Replacing a pump in an existing basin
Zoeller casts the M267's cap, motor housing, pump housing and base in iron, around a 1/2 HP split-capacitor motor. It passes 2 in solids, delivers 115 GPM at 5 ft and reaches 20.5 ft, and its float switches on at 12 in and off at 4 in. The minimum simplex basin is 18 in by 30 in, and Zoeller covers it for three years.
Liberty Pumps LE51A Sewage Pump
Best for: Long or busy drain runs
Liberty rates the 1/2 hp LE51A for 118 GPM at 10 ft of total head and 25 ft maximum, more flow at height than the other single pumps here. Its heavy cast iron body uses permanently lubricated ball bearings and a quick-connect cord that can be swapped without breaking the motor seal. Some listings quote a much higher flow; Liberty's own sheet is the figure to trust.
Wayne RPP50 Sewage Pump
Best for: Wide basins where longer cycles help
Wayne's RPP50 has an all cast iron motor housing and a tethered float that switches on at 16 in and off at 7.5 in, so each run empties a deep slice of the basin and the pump starts less often. It passes 2 in solids through a 2 in discharge and needs a basin at least 18 in across. The warranty is one year.
Liberty Pumps P382LE51 Pro380 Simplex Sewage System
Best for: New basement bathrooms
Liberty's P382LE51 arrives as a full simplex system: a polyethylene basin, a polypropylene cover with a separate access cover, and an LE51 pump. Its QuickTree float system lets you lift out the floats for service without pulling the pump. Discharge and vent take 2 in or 3 in NPT threads, and Liberty's three-year warranty applies.
Superior Pump 93015-U Sewage Pump and Basin System
Best for: A straightforward bathroom add-on
Superior pairs a cast iron and stainless steel sewage pump with a basin in the 93015, so the main parts arrive together. The maker rates it at 4800 GPH with no lift and 3600 GPH at 10 ft, with a 25 ft maximum, and it passes 2 in solids through a 2 in NPT discharge. The warranty is one year, shorter than Liberty's.
Side by side
| Pump | Type | Flow at height (maker) | Switch on / off | Warranty |
|---|---|---|---|---|
| Zoeller M267 Waste-Mate Sewage Pump | Pump | 115 GPM at 5 ft | 12 in / 4 in | 3 years |
| Liberty Pumps LE51A Sewage Pump | Pump | 118 GPM at 10 ft | Not stated on the data sheet | 3 years |
| Wayne RPP50 Sewage Pump | Pump | Curve published as a graphic | 16 in / 7.5 in | 1 year |
| Liberty Pumps P382LE51 Pro380 Simplex Sewage System | Pump, basin and cover | Curve published as a graphic | Not stated on the data sheet | 3 years |
| Superior Pump 93015-U Sewage Pump and Basin System | Pump and basin | 3600 GPH at 10 ft | Not stated on the data sheet | 1 year |
Figures: Zoeller technical data sheet FM2789, Model 267; Zoeller installation instructions FM2676, three-year warranty; Liberty Pumps LE50-Series sales literature; Liberty Pumps LE-Series installation manual 7034000; Wayne RPP50 cast iron sewage pump sell sheet; Liberty Pumps Pro380-Series simplex sewage system specification; Liberty Pumps Pro370 and Pro380 installation manual 7225000; Superior Pump 93015 product page and technical data.
How the list was narrowed
All sewage pumps and sewage systems on this site with maker documents were compared on solids handling, flow at a working lift, maximum head, switch type and levels, minimum basin size and warranty. Listings whose flow figures look too high for the motor were checked against the maker sheet, and the maker figure was used. Each pick had to serve a different install.
Who should skip this list
Skip an ejector if there is no room to dig in a basin; a macerating upflush system sits on the floor instead. Homes on a pressure sewer, or where the line runs long and uphill to the street, may need a grinder pump rather than an ejector. Clear groundwater belongs to a sump pump.
Final recommendation
If you have a basin, the Zoeller M267 is the dependable default and the Liberty LE51A the choice for more flow at height. Pick the Wayne RPP50 for a wide basin and fewer starts. For a new bathroom, start with a complete system: the Liberty P382LE51 for its float access and warranty, or the Superior 93015 for a simpler package.
Questions readers ask
What size sewage ejector pump do I need?
Most single basement bathrooms are served by a 1/2 HP ejector that passes 2 in solids, such as the five picks here. Check the flow at your total lift, including the vertical rise and pipe length, against the maker's curve or table.
Does a sewage ejector basin need a vent?
Yes. Codes require a sealed basin with a vent to the outside, so sewer gas does not enter the house and air can move as the level changes. Systems such as the Liberty P382LE51 have a threaded vent port in the cover.
How long do sewage ejector pumps last?
Use and maintenance decide it. Keep wipes, grease and rags out of the drains, and check the floats and check valve every year or so. The warranties here run from one to three years.
Can a sump pump be used for sewage?
No. A sump pump is built for clear water and small particles. Sewage needs a pump that passes 2 in solids in a sealed, vented basin, as plumbing codes require.




