Comparison ยท Well pumps

Flotec FP4122 vs Wayne SWS75

Two 3/4 HP cast iron shallow well jet pumps. The Flotec delivers more water at shallow lifts and lets you adjust the switch; the Wayne holds up better near 25 ft and carries three times the warranty.

By Pumpendium Editorial · Updated November 2026

Flotec FP4122 3/4 HP Convertible Jet Pump

Flotec FP4122 3/4 HP Cast Iron Jet Pump

3/4 HP Flotec cast iron jet for water within 25 ft.

Check price at MRO Supreme
vs
Wayne SWS75 3/4 HP Shallow Well Jet Pump

Wayne SWS75 3/4 HP Shallow Well Jet Pump

3/4 HP Wayne jet that holds flow well at deeper lifts.

Check price at MRO Supreme
Quick verdict

Choose the Flotec FP4122 when water sits within about 20 ft of the pump, you want the most flow at 40 PSI and you may need to raise the pressure switch settings later.

Choose the Wayne SWS75 when the water level drops close to 25 ft, you want the factory 30/50 settings left alone and you value a three-year warranty over peak flow.

Key specifications

SpecificationFlotec FP4122 3/4 HP Cast Iron Jet PumpWayne SWS75 3/4 HP Shallow Well Jet Pump
Horsepower3/4 HP3/4 HP
TypeShallow well jet, wells to 25 ftShallow well jet, water less than 25 ft below the pump
Flow at 0 ft, 40 PSI14.7 GPM (about 880 GPH)644 GPH (about 10.7 GPM)
Flow at 10 ft, 40 PSI12.8 GPM (about 770 GPH)586 GPH (about 9.8 GPM)
Flow at 20 ft, 40 PSI9.4 GPM (about 560 GPH)528 GPH (about 8.8 GPM)
Flow at 25 ft, 40 PSI7.3 GPM (about 440 GPH)499 GPH (about 8.3 GPM)
Pressure switch30/50 PSI, adjustable per Pentair's instructions30/50 PSI, preset and not adjustable
Maximum pressure70 PSINot stated in the manual
Voltage as shipped115/230 V, factory set for 230 V115/230 V, factory set for 115 V
ConstructionCast iron pump housingCast iron; thermoplastic impeller and diffuser, stainless shaft
Suction and discharge1-1/4 in NPT suction, 1 in NPT discharge1-1/4 in NPT suction, 1 in NPT discharge
Breaker15 A at 230 V, 20 A at 115 VNot stated in the manual
Tank pre-charge2 PSI below cut-in28 to 30 PSI
Warranty1 year3-year limited

Figures: Flotec FP4112 and FP4122 cast iron shallow well jet pump specification sheet 37843; Wayne shallow well jet pump operating instructions and parts manual 640002W-001 G; Pentair Flotec FP4122-08 product page; Pentair instructions for adjusting well pump pressure switches U80-129; Pentair shallow well pumps installation and operation manual P15002; Wayne SWS50, SWS75 and SWS100 shallow well jet pump sell sheet.

Scorecard

CriterionEdgeWhy
Flow at shallow liftsFlotec FP4122 3/4 HP Cast Iron Jet PumpAt 10 ft and 40 PSI Flotec rates 12.8 GPM, while Wayne's 586 GPH works out to under 10 GPM.
Flow near the 25 ft limitWayne SWS75 3/4 HP Shallow Well Jet PumpAt 25 ft and 40 PSI the Wayne holds about 8.3 GPM against 7.3 GPM for the Flotec.
Adjustable pressureFlotec FP4122 3/4 HP Cast Iron Jet PumpPentair explains how to raise the FP4122 switch; Wayne says changing its preset switch voids the warranty.
Warranty lengthWayne SWS75 3/4 HP Shallow Well Jet PumpWayne gives three years of limited coverage against one year for the Flotec.
Pipe connectionsEvenBoth use a 1-1/4 in NPT suction and a 1 in NPT discharge, so they swap without repiping.

Flow at each depth to water

A shallow well jet pump loses output as the water level drops, and these two lose it at different rates. Flotec's spec sheet, measured at 40 PSI, shows the FP4122 at 14.7 GPM with no lift, 12.8 GPM at 10 ft, 9.4 GPM at 20 ft and 7.3 GPM at 25 ft. Wayne's manual gives the SWS75 at 40 PSI as 644 GPH at 0 ft, 586 GPH at 10 ft, 528 GPH at 20 ft and 499 GPH at 25 ft.

Converted to the same unit, the Flotec leads clearly at shallow lifts, by about three gallons a minute at 10 ft. The gap closes as the lift grows, and right at 25 ft the Wayne edges ahead. If your water table sits within about 15 ft of the pump, the Flotec gives more water to showers and sprinklers. If it falls near 25 ft in a dry summer, the Wayne's flatter curve is the steadier performer. See our guide to shallow and deep well pumps if your water is any deeper.

Pressure range and the switch

Both pumps ship with a 30/50 PSI pressure switch, meaning they start at 30 PSI and stop at 50 PSI. Wayne states plainly that its switch is preset, not adjustable and that changing it voids the warranty. The Wayne manual also lists flow at 30 and 50 PSI, which shows output dropping to 451 GPH at 10 ft once the tank nears cut-out.

Pentair publishes instructions for adjusting the switch on its jet pumps. Each full turn of the main nut raises both settings by about 2-1/2 PSI, the cut-in should never go below 20 PSI and the cut-out never above 60 PSI. With a rated maximum of 70 PSI, the FP4122 has room for a 40/60 setting if you want stronger showers. Our guide to pressure switch settings explains how to change them safely.

Voltage and wiring

Both motors are dual voltage, but they leave the factory set differently. The Flotec FP4122 arrives wired for 230 V, and Pentair's manual shows how to move the voltage plug or dial to 115 V. Pentair recommends a 15 A breaker at 230 V or a 20 A breaker at 115 V. The Wayne SWS75 comes set for 115 V and can be converted to 230 V.

Neither pump has a plug; both are wired in the field at the pressure switch. Running a 3/4 HP motor on 230 V draws half the current of 115 V and allows lighter wire on a long run to a well house, so many installers choose 230 V where it is available. Whichever you use, confirm the motor setting matches the supply before switching on, since the wrong voltage can burn out the motor and void the warranty.

Tank and priming

Neither pump works without a pressure tank. Wayne's manual explains that a precharged tank should be set to 28 to 30 PSI when empty, and Pentair tells owners to set it 2 PSI below the switch cut-in, which also lands at 28 PSI for a 30/50 switch. If you raise the Flotec switch, lower or raise the tank pre-charge to match. Our tank sizing guide covers drawdown.

Priming is the same routine on both. Install a foot valve, fill the pump body through the priming plug and start the motor. Wayne says to stop and refill if the pump has not primed within five minutes. Both suction lines must be rigid, airtight and sloped upward to the pump, because a small air leak is the most common reason a shallow well pump loses prime.

Warranty and service

Wayne backs the SWS75 for three years, Flotec the FP4122 for one. That is a real difference for a pump that runs every time someone opens a tap. Wayne voids coverage if the pump runs dry, pumps anything but clear water, freezes or sits outdoors without protection. Pentair says freezing voids its warranty too and warns never to run the pump dry, so a heated pump house or basement location matters for either.

Wayne lists a thermoplastic impeller and diffuser and a stainless steel shaft, and Pentair publishes a parts list for the FP4112 and FP4122 so seals and impellers can be replaced. Note that our catalog files the FP4122 with convertible jets, but Pentair sells it as a shallow well pump, and this comparison treats it that way.

Who each one fits

The Flotec FP4122 3/4 HP Cast Iron Jet Pump fits if

  • Water sits within about 15 to 20 ft.
  • You want the most flow at a shallow lift.
  • You may raise the switch to 40/60 later.
  • A 230 V circuit is already run to the pump.

Full reference

The Wayne SWS75 3/4 HP Shallow Well Jet Pump fits if

  • The water level can fall close to 25 ft.
  • You prefer a fixed 30/50 switch.
  • A three-year warranty is worth more than peak flow.
  • Your supply circuit is 115 V.

Full reference

Questions readers ask

Is Flotec or Wayne better for a shallow well?

On these two 3/4 HP models, the Flotec FP4122 gives more water when the lift is short, while the Wayne SWS75 holds slightly more flow near the 25 ft limit and carries a three-year warranty. Your depth to water and how much you value warranty decide it.

Can either pump draw water from deeper than 25 ft?

No. Both are shallow well jet pumps rated for water no more than 25 ft below the pump. For deeper water you need a convertible jet with an ejector in the well, or a submersible pump. Pushing a shallow well pump past its lift causes lost prime and very low flow.

Can I swap a Wayne SWS75 for a Flotec FP4122?

Usually. Both have a 1-1/4 in NPT suction and a 1 in NPT discharge, both use a 30/50 switch and both run on 115 or 230 V. Check which voltage the motor is set for before wiring, because the Flotec ships at 230 V and the Wayne at 115 V.

Can I raise the pressure on the Wayne SWS75?

Wayne says its switch is factory set at 30 on and 50 off and must not be changed, and that changing it voids the warranty. If you want higher pressure, the Flotec FP4122 is the better choice, since Pentair documents how to adjust its switch.

Final verdict

These are close rivals in size and plumbing, so the decision rests on depth and priorities. The Flotec FP4122 is the stronger pump at shallow lifts and the more flexible one if you want higher pressure, but it carries a one-year warranty. The Wayne SWS75 gives up some flow near the surface, holds on slightly better near 25 ft and comes with three years of cover.

How we research · Disclosure