In Liberty's sump range the first two digits give the series (230, 250, 280, 290) and the last digit gives the switch: 0 is manual, 1 an integral wide-angle float, 3 a wide-angle float on a piggyback plug and 7 a vertical magnetic float. A -2 suffix means a 25 ft cord. The Pro380 is a complete sewage basin system built around an LE-series pump such as the LE51.
The sump pump series: 230, 250, 280 and 290
Liberty's installation manual 7035000R groups its dewatering and effluent pumps by series: the 250-Series at 1/3 hp, the 280-Series at 1/2 hp and the 290-Series at 3/4 hp, all cast iron. The 230-Series is the odd one out, a 1/3 hp pump with a powder-coated aluminum motor housing and polypropylene parts, which Liberty says cools better than cast iron.
Within each series the motor and impeller are the same; what changes is the switch. That is why the 257 and the 253 pump alike but behave very differently in a pit. The 287 is the 1/2 hp version of the 257, with the same vertical magnetic float and a higher on level.
| Series | Power | Build | Discharge | Solids |
|---|---|---|---|---|
| 230 (237) | 1/3 hp | Aluminum and polypropylene | 1-1/2 in | 3/8 in |
| 250 (253, 257) | 1/3 hp | Cast iron | 1-1/2 in | 1/2 in |
| 280 (283, 287) | 1/2 hp | Cast iron | 1-1/2 in | 3/4 in |
| 290 (293, 297) | 3/4 hp | Cast iron | Not stated in these sheets | Not stated in these sheets |
Figures: Liberty Pumps installation manual 7035000R, 250/280/290 and FL series; Liberty 230-Series sales literature; Liberty 250-Series sales literature, models 253 and 257; Liberty 280-Series sales literature, models 283 and 287.
The last digit is the switch
Liberty's sales sheets list four switch options for each series: manual with no switch, a heavy-duty vertical magnetic float, an integral wide-angle float, and a wide-angle float with a piggyback plug. The manual's float table and wording map these to model numbers. Models ending in 0 have no switch and need a separate control. Models ending in 3 carry a wide-angle float with its own cord and piggyback plug, which Liberty designed so the pump can be run by hand if the switch fails. Models ending in 1 and 7 have factory-preset switches that cannot be adjusted, the 7 being the vertical magnetic float.
The levels differ a lot, which matters for basin size. Liberty lets its vertical-float 257, 287 and 297 work in a 10 in pit, while it recommends 14 in for the others.
| Model | Switch | Off level | On level |
|---|---|---|---|
| 250, 280, 290 | None (manual) | 4 in minimum | Set by user |
| 251, 253 | Wide-angle float | 4 in | 11 in |
| 257 | Vertical magnetic float | 4 in | 7 in |
| 281, 283 | Wide-angle float | 7 in | 13 in |
| 287 | Vertical magnetic float | 4 in | 9.5 in |
| 297 | Vertical magnetic float | 4 in | 9.5 in |
Figures: Liberty Pumps installation manual 7035000R, 250/280/290 and FL series.
Suffixes: cord length, voltage and alarms
Letters and numbers after the dash change options rather than the pump. Liberty's LE50 literature spells it out: the standard cord is 10 ft, a -2 suffix gives a 25 ft cord, and on manual models -3 and -5 give 35 ft and 50 ft bare-lead cords. A model ending in 2 instead of 1 in the sewage range, such as the LE52, is the 208–230 V version. On sewage pumps the letter after the number gives the switch: M for manual, A for automatic wide-angle float and AV for a vertical float.
Systems add their own tags. EYE on a model such as the PC257-442-10A-EYE or SJ10A-EYE means Liberty's NightEye wireless alarm is built in, and an A on the SJ10 means a standard alarm.
Sewage pumps and the Pro380 system
The LE50-Series are Liberty's 1/2 hp cast iron sewage pumps: 2 in solids handling, a 2 in FNPT discharge and a 25 ft maximum head, with Liberty quoting 118 GPM at a 10 ft head. The LE51A is the 115 V automatic version with a wide-angle float.
The Pro380 is not a different pump. It is a pre-assembled simplex sewage system: a rotationally molded polyethylene basin about 24 in across, a cover with 2 in or 3 in NPT connections for discharge and vent, and Liberty's QuickTree float system, which lets the floats come out without pulling the pump. The model number names the pump inside: the P382LE51 holds an LE51, and Liberty's spec sheet lists versions from 4/10 hp to 3/4 hp. The Pro370 (P373) range uses a smaller basin for lighter duty.
Drain, backup, utility and transfer models
A handful of Liberty products sit outside those series. The 404 is a 1/3 hp drain pump system only 11 in tall, built for sinks, laundry and dehumidifiers below a gravity line. The SJ10 is a water-powered backup that runs off municipal pressure between 20 PSI and 100 PSI and needs no electricity. The PC442 series pairs a 1/3 or 1/2 hp primary pump with a 12 V DC backup and controller in one assembly; the PC257-442 uses a 257 as the primary. For portable jobs, the 260 is a 1/6 hp utility pump with a 25 ft cord, and the 331 is a 1/2 hp transfer pump with a maximum head of 105 ft.
To compare Liberty's sump pumps with other brands at the same power, see the cast iron sump pump list.
Common mistakes
- Ordering a 257 to replace a 253 and finding the float range much shorter.
- Using a vertical-float model for a septic effluent job; Liberty advises against it.
- Dropping the cord suffix and receiving a 10 ft cord instead of 25 ft.
- Buying a 208–230 V model for a standard 115 V outlet.
- Assuming a Pro380 is a bare pump rather than a full basin system.
Products that fit

Liberty Pumps 257 Sump Pump
Series 250 with a vertical magnetic float, preset at 4 in off and 7 in on.

Liberty Pumps 287 Sump Pump
Series 280 at 1/2 hp with the same vertical float design.

Liberty Pumps 253 Sump Pump
Series 250 with a wide-angle float on a piggyback plug.

Liberty Pumps 237 Sump Pump
Aluminum-bodied 1/3 hp sump pump from the 230-Series with a vertical float.

Liberty Pumps P382LE51 Pro380 Simplex Sewage System
Pro380 sewage basin system built around the 1/2 hp LE51 pump.

Liberty Pumps PC257-442 Combo Sump Pump System
Primary 257 and 12 V battery backup assembled as one unit.
Questions readers ask
What is the difference between the Liberty 257 and 287?
Both are cast iron sump pumps with a vertical magnetic float. The 257 is 1/3 hp from the 250-Series and turns on at 7 in; the 287 is 1/2 hp from the 280-Series and turns on at 9.5 in. Both turn off at 4 in.
What is a Liberty Pro380?
It is a pre-assembled simplex sewage system: polyethylene basin, sealed cover, QuickTree float mount and an LE-series sewage pump. The P382LE51 version uses the 1/2 hp LE51 pump, and other versions range from 4/10 hp to 3/4 hp.
What does -2 mean on a Liberty pump?
It means the pump comes with a 25 ft power cord instead of the standard 10 ft cord. Liberty uses -3 and -5 for 35 ft and 50 ft bare-lead cords on manual models.
Can I adjust the float on a Liberty 257?
No. Liberty states the switches on models 251, 257, 281, 287, 291 and 297 are factory preset. For a different range, use a model with a tethered wide-angle float, such as the 253, or a separate switch.