The CDU790 (1/3 HP) and CDU800 (1/2 HP) have coated steel housings and a three-year warranty. The CDU980E (3/4 HP) and CDU1000 (1 HP) step up to stainless steel and a five-year warranty. All four use a vertical float at about 9 in on and 4 in off, a 1-1/2 in NPT discharge and Wayne manual 600002W-001.
The CDU lineup at a glance
Wayne builds its main sump pumps as a ladder. Each step adds horsepower, and the top two also change the motor housing from epoxy-coated steel to stainless steel. Every model in the ladder keeps the same essentials: a 120 V permanent split capacitor motor in an oil bath, a cast iron volute, a thermoplastic impeller, top suction that pulls water from above the pit floor, and an integrated vertical float guarded against the basin wall.
Because the switch and footprint are shared, all four fit an 11 in or larger basin and drop into the same plumbing. That makes upgrading from a CDU790 to a CDU800 a straight swap if your old pump struggles at your lift.
| Model | Horsepower | Motor housing | Warranty | Pump part number |
|---|---|---|---|---|
| CDU790 | 1/3 HP | Coated steel | 3 years | 56137-WYN3 |
| CDU800 | 1/2 HP | Coated steel | 3 years | 56270-WYN3 |
| CDU980E | 3/4 HP | Stainless steel | 5 years | 58321-WYN3 |
| CDU1000 | 1 HP | Stainless steel | 5 years | 58321-WYN2 |
Figures: Wayne submersible sump pump manual 600002W-001 J; Wayne coated steel sump pump sell sheet, CDU790 and CDU800; Wayne stainless steel sump pump sell sheet, CDU980E and CDU1000.
How much water each one moves at your lift
Wayne publishes flow at every 5 ft of lift, which makes these pumps easy to size. The gap between neighbours stays fairly even at low lift and widens as the water has to climb. At 20 ft, the CDU1000 delivers more than three times the CDU790's output. Measure from the water in the pit to the highest point of your discharge, add a little for long horizontal runs, and read across.
Two caveats. Wayne's sell sheets print per-minute figures that do not convert neatly from the manual's hourly table, and the CDU1000 product page shows 5,640 GPH at 5 ft where the current manual shows 5,460. The manual figures are used here. If the choice is close, run your numbers through the sump pump sizing calculator.
| Model | 0 ft | 5 ft | 10 ft | 15 ft | 20 ft |
|---|---|---|---|---|---|
| CDU790 (1/3 HP) | 4,600 | 3,810 | 3,060 | 2,220 | 1,200 |
| CDU800 (1/2 HP) | 5,100 | 4,500 | 3,840 | 3,060 | 2,040 |
| CDU980E (3/4 HP) | 5,490 | 5,076 | 4,600 | 4,100 | 3,500 |
| CDU1000 (1 HP) | 6,100 | 5,460 | 5,100 | 4,560 | 3,840 |
SS, CI and ET variants, and the other Wayne sump pumps
The same manual covers several letter variants. CDU790SS and CDU800SS have stainless housings; CICDU790 and CICDU800 have cast iron housings; both carry five years of coverage instead of three. CDU980ET and CDU1000ET are listed alongside the base stainless models with the same performance and warranty. Their flow matches the plain model of the same horsepower, so the choice between them is about the housing and the coverage, not output.
The manual also covers cheaper Wayne pumps that are easy to confuse with the CDU line. The SPF33 and SPF50 have thermoplastic volutes and a one-year warranty, the CDT50 uses a tether float, and the WST33 has a reinforced thermoplastic housing. A tether float needs a 14 in basin, starts at about 13 in and stops at about 7 in, and Wayne requires its switch to be replaced every two years.
Which Wayne model should you buy?
For most basements with a lift under about 10 ft, the CDU790 is enough, and the CDU800 is the safer pick where the pit fills quickly or the discharge climbs higher. Wayne's 1/3 versus 1/2 decision is covered in more depth in the 1/3 vs 1/2 HP guide.
The CDU980E and CDU1000 earn their place in two cases: a high lift, where their flow at 15 and 20 ft is far stronger, and corrosive or long-service pits where the stainless housing and five-year warranty matter. They are not a cure for short cycling in a small basin; a stronger pump empties the pit faster and starts more often.
- Measure the vertical lift from pit water to the highest pipe point.
- Find the row in the flow table at that lift.
- Check that your basin is at least 11 in across.
- Choose stainless if the pit water is aggressive or you want five years of cover.
Wayne manuals, including battery backups
All four CDU pumps share the sump manual 600002W-001, whose current revision is J. It contains the specification table, the troubleshooting chart, the repair kits and the warranty. Wayne prints a QR code on the first page that leads to the online manual library, and the product pages link the same file.
Wayne's battery backups have their own manuals. The ESP25n is a 12 V backup rated at 2,700 GPH at zero lift and 1,500 GPH at 10 ft, covered by manual 600005W-001; the older ESP25 has manual 352207-001. The WSS30VN combines a 1/2 HP primary with a 12 V backup in one preassembled unit for a 16 in basin, covered by manual 670006W-001.
| Model | Type | Manual | Rating |
|---|---|---|---|
| ESP25n | 12 V backup pump | 600005W-001 | 2,700 GPH at 0 ft, 660 GPH at 15 ft |
| ESP25 | 12 V backup pump (earlier) | 352207-001 | Not compared here |
| WSS30VN | 1/2 HP primary plus 12 V backup | 670006W-001 | Primary 64 GPM at 5 ft |
Figures: Wayne ESP25n operating instructions and parts manual 600005W-001 J; Wayne ESP25 owner's manual 352207-001; Wayne WSS30VN combination system sell sheet; Wayne WSS30VN operating instructions 670006W-001 I.
Warranty, serial numbers and registration
Wayne's warranty covers the original purchaser only and runs from the purchase date if you can show a receipt from an authorized dealer. Without proof of purchase it runs from the manufacture date instead, so keep the receipt with the manual. A claim needs a return authorization number, the model and serial number, and the proof of purchase, and you pay shipping to Wayne while Wayne pays the return. The warranty is voided by poor maintenance, and Wayne asks owners to inspect the pump three to four times a year.
Write the model, serial number and install date in the space Wayne provides on the last page of the manual. For a fair comparison with other brands, the cast iron sump pump list sets the CDU pumps beside Zoeller and Liberty.
Common mistakes
- Buying the 1 HP CDU1000 for a small pit where it will short cycle.
- Assuming the SPF33 or WST33 has the same warranty as the CDU790.
- Fitting a tether-float Wayne pump in a basin narrower than 14 in.
- Throwing away the receipt, which moves the warranty start to the build date.
- Ordering a float kit without checking the pump's model and serial number.
Products that fit

Wayne CDU790 Sump Pump
1/3 HP coated steel entry model with a three-year warranty.

Wayne CDU800 Sump Pump
1/2 HP coated steel model with more flow at every lift.

Wayne CDU980E Sump Pump
3/4 HP stainless steel model with five years of coverage.

Wayne CDU1000 Sump Pump
1 HP stainless steel top of the range for high lifts.

Wayne WSS30VN Primary and Battery Backup Sump Pump System
Preassembled 1/2 HP primary and 12 V backup for a 16 in basin.
Questions readers ask
What is the difference between the Wayne CDU790 and CDU800?
Only the motor. The CDU790 is 1/3 HP and the CDU800 is 1/2 HP; both have coated steel housings, the same vertical float and a three-year warranty. The CDU800 moves 3,840 GPH at 10 ft against 3,060 GPH for the CDU790.
Which Wayne model is 56137-WYN3?
That is the pump part number Wayne prints for the CDU790 on its sell sheet. The CDU800 is 56270-WYN3, the CDU980E is 58321-WYN3 and the CDU1000 is 58321-WYN2. Some retail listings show these part numbers instead of the model.
Where can I find the Wayne sump pump manual?
The CDU pumps share manual 600002W-001, currently revision J, available from the Wayne manual library and each product page. It includes the specification table, troubleshooting chart, repair kits and warranty terms.
Does Wayne make a 3/4 HP sump pump?
Yes, the CDU980E. It has a stainless steel housing, a cast iron volute, the same vertical float as the smaller models and a five-year warranty, and Wayne rates it at 3,500 GPH at a 20 ft lift.