Cast iron sewage ejector · Liberty Pumps

Liberty Pumps LE41A Sewage Pump

The Liberty LE41A is the 4/10 hp, 115 V member of the LE40-Series: an oil-filled cast iron sewage pump with a vortex impeller that passes 2 in spherical solids and a piggyback wide-angle float.

Model LE41A · part number LE41A · Updated November 2026

Horsepower
4/10 hp
Voltage
115 V, single phase
Max flow
142 GPM (listing; its bullets say 143 GPM)
Max head
20 ft (listing)

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Quick verdict

In short

The LE41A is a fit for a home basement bathroom where the sewer connection is not far above the basin, and where you want Liberty's quick-connect cord and piggyback switch in a lighter package than the 1/2 hp LE51A. Liberty's own LE40 data sheet is not among the saved documents, so flow and head below come from the retail listing; check them against the maker's curve before you rely on them.

Who it fits, and who should skip it

A good fit if

  • The lift from the basin to the sewer is short and a 4/10 hp pump is enough.
  • You want a cord that unplugs from the motor and can be swapped in the field.
  • Your basin is at least 18 in wide and 24 in deep.

Look elsewhere if

  • The listing's 20 ft maximum head is close to your total head.
  • You need maker-printed flow figures before you buy.

Specifications

Motor

Horsepower4/10 hp
Voltage115 V, single phase
Full-load amps12 A (22.5 A locked rotor), per Liberty's LE41 system table
Motor typeOil-filled, thermally protected

Figures: Liberty Pumps installation manual 7034000N, LE and LEH-Series; Amazon listing B001DEMDRU; Liberty Pumps Pro380-Series system specification R05/2026.

Performance

Max flow142 GPM (listing; its bullets say 143 GPM)
Max head20 ft (listing)
Maker curveNot stated on the saved Liberty documents

Figures: Amazon listing B001DEMDRU; Liberty Pumps installation manual 7034000N, LE and LEH-Series.

Switch

Switch typeWide-angle float on a piggyback plug
On / off levelsOn at 15 in, off at 7 in (factory set)

Figures: Liberty Pumps installation manual 7034000N, LE and LEH-Series.

Build

Solids handling2 in spherical solids, vortex impeller
HousingCast iron
Power cord10 ft quick-disconnect
Max liquid temperatureDo not run in fluid above 140 °F
Weight39 lb (listing)
Minimum basin18 in diameter, 24 in deep
Warranty3-year limited on Liberty wholesale products; listing text says 2 years

Figures: Amazon listing B001DEMDRU; Liberty Pumps installation manual 7034000N, LE and LEH-Series; Liberty Pumps installation manual 7225000L, wholesale products warranty.

Versions

Liberty's manual lists two automatic LE40 switch styles with different factory float points.

VersionPart numberWhat differsListing
LE41A, wide-angle float, 115 VLE41AOn near 15 in, off near 7 in, 10 ft cordView on Amazon
LE41AV, vertical float, 115 VLE41AVOn near 11 in, off near 5.5 in, for narrower basinsNot linked

Figures: Liberty Pumps installation manual 7034000N, LE and LEH-Series; Amazon listing B001DEMDRU.

Installation and setup

Liberty's manual for the LE and LEH-Series sets a minimum sealed basin of 18 in across and 24 in deep, larger if the fixture count or code requires it. Put the pump on a clean, level floor and keep the float out of the path of water falling from the inlet.

A check valve is required after the pump, followed by a gate valve so the check valve can be cleaned without draining the line. Do not reduce the pipe below the pump's own outlet, and keep the run short with few bends. The basin must be sealed and vented; venting through the inlet to an existing stack works only when no trap sits between them.

Plug into a separately fused, grounded branch circuit. For basements the outlet should sit at least 4 ft above the floor, and an extension cord is not allowed.

Switch and sizing notes

Liberty sets the wide-angle float on the LE40-Series to start the pump at about 15 in and stop it near 7 in. That off level is the minimum depth that keeps the motor covered and cool, so if you tether the float for a different range, never let the basin pump lower. Allow at least 3-1/2 in of cord between the tether point and the float.

Liberty's LE40 curve was not among the saved documents, so the only figures here are the listing's 142 GPM and 20 ft. Treat 20 ft as the point where flow stops, add pipe friction to your vertical lift, and ask Liberty or your supplier for the flow at your total head before committing.

Ownership and maintenance

The oil-filled motor needs no routine lubrication. What it needs is a basin free of wipes, grease and hygiene products, and a float that can still swing. A spare pump left in storage for more than three months should have its impeller turned by hand once a month to keep the seals wet.

If the float fails, separate the piggyback plug and plug the pump straight into the outlet to run it manually until a new switch arrives. Repairs under warranty go through a Liberty-approved service center.

Pros and cons

Pros

  • Its vortex impeller clears 2 in spherical solids.
  • Quick-disconnect cord replaces without opening the motor.
  • Piggyback plug allows manual running.
  • Lighter than the 1/2 hp LE51A.

Cons

  • No maker flow figures in the saved documents.
  • Listing gives two different flow numbers.
  • Wide-angle float needs room to swing.

Alternatives worth comparing

Final verdict

The LE41A brings Liberty's serviceable LE-Series design to smaller jobs. Its weak point is paperwork rather than hardware: confirm flow at your head with the maker, and choose the LE51A if you want published numbers or more margin.

Where to buy

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Questions buyers ask

What is the difference between the Liberty LE41A and LE51A?

Both are LE-Series cast iron sewage pumps with piggyback wide-angle floats and quick-connect cords. The LE41A is 4/10 hp; the LE51A is 1/2 hp and carries published maker figures of 141 GPM at 5 ft. The LE41A's float also starts a little higher, near 15 in.

How much head can the LE41A handle?

The retail listing gives a maximum head of 20 ft, which is the height where flow stops. Liberty's own curve for the LE40-Series was not among the saved documents, so ask for the flow at your actual total head before relying on it for a tall lift.

Can the LE41A float be moved?

Yes, by tethering its cord to the discharge pipe, with at least 3-1/2 in of cord between the tether and the float. Whatever range you set, the pump must still stop with about 7 in of liquid in the basin so the motor stays submerged and cool.

Can I run the LE41A without its float switch?

Temporarily. The float cord has a piggyback plug, and the pump cord plugs into its back. If the switch fails, unplug the pump cord and plug it directly into the outlet, then switch it off at the breaker once the basin is down to keep it from running dry.