4 in deep well submersible ยท Red Lion

Red Lion RL12G05-2W1V 115 V Submersible Well Pump

The RL12G05-2W1V is the only 115 V pump in Red Lion's RL range: a 1/2 HP, 2-wire submersible for 4 in wells, rated at 12 GPM with 212 ft of shut-off head and a 12 A draw.

Model RL12G05-2W1V · part number 14942401 · Updated November 2026

Horsepower
1/2 HP
Voltage
115 V single phase
Max flow
12 GPM rated flow
Max head
212 ft (64.6 m) shut-off
Discharge
1-1/4 in FNPT thermoplastic

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Quick verdict

In short

This model exists for one situation: a cabin or older property where the well circuit is 115 V and rewiring for 230 V is not practical. Hydraulically it matches the 230 V 1/2 HP RL pumps. The catch is current. At 12 A it needs heavier cable for the same run, so check the cable before assuming a swap is simple.

Who it fits, and who should skip it

A good fit if

  • A well circuit that only carries 115 V.
  • Short to moderate cable runs from the panel to the pump.
  • Drilled wells of at least 4 in where the water stays fairly high.

Look elsewhere if

  • Long drop and service cable runs, where 230 V keeps voltage drop down.
  • Wells whose total head approaches 212 ft.

Specifications

Motor

Horsepower1/2 HP
Voltage115 V single phase
Amps12 A
Wiring2-wire plus ground, no control box

Figures: Red Lion 4-inch deep well submersible pump owner's manual 106720101 Rev. 003; Red Lion 4 in Submersible Well Pumps RL Series product page; Red Lion 4 in submersible well pumps RL series spec sheet.

Performance

Max flow12 GPM rated flow
Max head212 ft (64.6 m) shut-off

Figures: Red Lion 4-inch deep well submersible pump owner's manual 106720101 Rev. 003; Red Lion 4 in Submersible Well Pumps RL Series product page.

Application

Well size4 in diameter and larger
Minimum setting5 ft off the well bottom

Figures: Red Lion 4-inch deep well submersible pump owner's manual 106720101 Rev. 003.

Build

Discharge1-1/4 in FNPT thermoplastic
ShellStainless steel, thermoplastic motor bracket
IntakeSuction screen and check valve built in
Carton34.5 in long, 25 lb
Switch typeSeparate pressure switch required
Warranty3-year limited

Figures: Red Lion 4-inch deep well submersible pump owner's manual 106720101 Rev. 003; Red Lion 4 in submersible well pumps RL series spec sheet.

Versions

All three 1/2 HP RL pumps share one hydraulic end and the same 212 ft shut-off; they differ in supply voltage and motor wiring.

VersionPart numberWhat differsListing
RL12G05-2W1V, 2-wire, 115 V1494240112 AView on Amazon
RL12G05-2W2V, 2-wire, 230 V149424026 ANot linked
RL12G05-3W2V, 3-wire, 230 V149424056 A; control box includedNot linked

Figures: Red Lion 4-inch deep well submersible pump owner's manual 106720101 Rev. 003.

Installation and setup

The mechanical work is the same as for any RL pump: set it from the well record so it stays submerged at full draw-down, keep it at least 5 ft off the bottom and above the screen, hang it on a safety cable, fit a torque arrestor just above it, and tape the cable to the drop pipe every 10 ft.

The electrical side deserves more thought. A 115 V motor draws twice the current of its 230 V twin, and voltage lost in the cable rises with current and length. Red Lion's troubleshooting chart names low voltage as a cause of weak output, and an undersized cable also makes the motor work hotter at start-up. Use the cable size from the motor maker's table for your total run, splice with a proper kit, and confirm insulation with a megger before lowering.

A GFCI and a fused disconnect are required by the manual.

Switch and sizing notes

As a 2-wire pump it runs directly from a pressure switch, which must be rated for the motor's 12 A or drive a contactor. The switch settings guide explains cut-in and cut-out choices.

Size by total head: pumping level, height to the tank, tank cut-out pressure in feet and friction. Keep the sum comfortably below 212 ft. If your service has 230 V available, the RL12G05-2W2V does the same job at half the current. The shallow versus deep well guide helps if the water is near the surface.

Ownership and maintenance

Once installed, most problems show up as cycling or low output. Red Lion points cycling toward leaks, a waterlogged or small tank, or a switch set too high or mounted too far from the tank. Low output points toward a blocked intake screen, a weak well, low voltage or wear.

The built-in check valve unscrews with a T-handle wrench (left-hand thread) for cleaning. The motor is covered for three years through an authorized reseller; opening it voids that cover.

Pros and cons

Pros

  • Runs on a 115 V well circuit.
  • No control box to mount.
  • Same pump end as the 230 V models.
  • Three-year warranty from Red Lion.

Cons

  • Draws 12 A, twice the 230 V version.
  • Needs heavier cable on long runs.
  • Limited to 212 ft of shut-off head.

Alternatives worth comparing

Final verdict

Buy the RL12G05-2W1V when a 115 V well circuit is a fixed constraint and the cable run is reasonable. If 230 V is available, the 2W2V twin delivers the same water with half the current and fewer wiring worries.

Where to buy

Each button opens this exact model's listing. We may earn a commission on tracked links; it never changes what we publish. Disclosure

Questions buyers ask

Why choose a 115 V well pump?

Only when the circuit at the well is 115 V and changing it is impractical. Most 4 in submersibles are 230 V because half the current means smaller cable and less voltage drop. Red Lion offers this single 115 V option in the RL line.

Is the RL12G05-2W1V weaker than the 230 V version?

No. Red Lion lists the same 12 GPM rating and 212 ft shut-off for the 115 V and 230 V 1/2 HP pumps. The difference is current: 12 A here against 6 A, which matters for cable size and switch rating.

Can I swap it into a 230 V installation?

Not without changing the supply. Connecting a 115 V motor to 230 V will destroy it. Match the pump to the voltage at the switch, or choose the RL12G05-2W2V, which uses the same pump end on 230 V.

How far off the bottom should it hang?

At least 5 ft above the bottom of the well and above the screen or casing perforations, unless water is known to flow past the motor. The pump must stay submerged at the lowest pumping level.