Guide · Well pumps

Flotec pumps (FP4122 jet, FP22 submersibles): specs, warranty and troubleshooting

Flotec is Pentair's retail pump line, sold for shallow wells, deep wells and basements. Pentair's own manuals and spec pages give the figures to judge them and a detailed troubleshooting chart for when one stops.

By Pumpendium Editorial · Updated November 2026

The short answer

Flotec pumps are Pentair products with published specs and warranties: one year on the FP4122 shallow well jet pump, three years on the FP2211 submersible and five on the E75STVT sewage pump. When a Flotec jet pump runs but delivers no water, Pentair says to check prime first; when it will not run, check power, the starting switch and dirty pressure switch contacts.

Are Flotec pumps any good?

Judge them on what Pentair publishes. The FP4122 is a 3/4 HP cast iron shallow well jet pump with a dual-voltage motor and a factory 30/50 psi switch, rated for depths to water of 25 ft or less. The FP2211 is a 1/2 HP two-wire 4 in submersible with a stainless steel pump and motor housing and a floating stack impeller design Pentair describes as resisting sand lock. The E75STVT is a 3/4 HP cast iron sewage pump with a PSC motor.

Warranty length is the clearest signal of the maker's own confidence, and it varies by product. The table sets it beside the key ratings. Flotec documents are thorough and Pentair-branded, which makes service easier than for brands with no published manual.

Flotec models from Pentair spec pages and sheets
ModelTypePowerKey ratingWarranty
FP4122Shallow well jet, cast iron3/4 HP12.8 GPM at 10 ft lift and 40 psi1 year
FP22112-wire 4 in submersible, 115 V1/2 HP8.1 GPM at 100 ft3 years
FP22222-wire 4 in submersible, 230 V3/4 HP11.7 GPM at 100 ftNot stated on the sell sheet
E75STVTCast iron sewage3/4 HP125 GPM at 10 ft lift5 years

Figures: Pentair Flotec FP4122-08 product page; Pentair Flotec FP2211 product page; Flotec 2-wire 4 in submersible sell sheet; Pentair Flotec E75STVT product page.

Flotec jet pump will not run

Pentair's shallow well manual lists five causes for a motor that will not run: the disconnect switch is off, a fuse is blown or the breaker tripped, the motor's starting switch is defective, wiring at the motor is loose or wrong, and the pressure switch contacts are dirty. For dirty contacts its fix is simple: disconnect power and file the contacts with an emery board or nail file.

It also warns that capacitor voltage can be hazardous and describes discharging the capacitor safely before touching it; if you are unsure, use an electrician. A motor that runs hot and trips its overload is usually wired for the wrong voltage, fed too low a voltage through undersized wire, or cycling too often. The FP4122 ships wired for 230 V; Pentair's page notes the manual covers converting it to 115 V.

Runs but delivers no water

Pentair's chart gives a clear instruction here: stop the pump and check prime before looking for other causes. Unscrew the priming plug and see whether water fills the priming hole. On a pump that has never run properly, Pentair blames poor priming, suction air leaks or a foot valve or check valve that leaks. In a system already in use, the pump loses prime through air leaks or because the water level has fallen below the suction pipe.

Other causes include a plugged foot valve, strainer, ejector or impeller, a valve stuck shut, frozen pipes and a foot valve buried in sand or mud. Pentair's answer for a falling water table is direct: if the water level drops beyond 25 ft, a shallow well pump cannot reach it and a deep well setup is needed.

  1. Switch off power and remove the priming plug.
  2. If the casing is not full, refill it and the suction line with water.
  3. Check suction joints for air leaks with soapy water.
  4. Clean or replace a plugged or leaking foot valve.
  5. Clear the nozzle, venturi and impeller if flow stays weak.

Will not shut off or cycles too often

For a pump that delivers water but will not stop, or cycles too often, Pentair lists a pressure switch out of adjustment or with welded contacts, faucets left open, a clogged venturi, nozzle or impeller, a waterlogged standard tank, leaking pipes or foot valve, and too little air in a pre-charged tank. Its tank fix is to relieve all pressure, read the air valve with a tire gauge and pump air in until it sits 2 psi below the switch cut-in. Pentair's separate switch instructions explain adjusting the nuts.

Air spurting from faucets usually means the pump is still picking up prime, the suction side leaks, the well is gaseous or the pump is drawing the well down below the foot valve.

Flotec 4 in submersibles

The FP2211, FP2212 and FP2222 are two-wire pumps, so there is no control box above ground; the starting parts are in the motor. Pentair's sell sheet shows how quickly output falls with depth: the 1/2 HP FP2211 moves 13.2 GPM at 20 ft but 2 GPM at 150 ft, while the 3/4 HP FP2222 still gives 8.8 GPM there. Choose by your depth to water, not horsepower alone, and see the deep well submersible pump list for alternatives. For electrical faults on submersibles, the no-water checklist covers breakers and wiring.

Parts, manuals and the catalog label

Pentair publishes the shallow well manual, a parts list for the FP4112 and FP4122, spec sheets and the pressure switch adjustment instructions on each product page. One caution: some retailers, and older catalog records, call the FP4122 a convertible jet pump. Pentair's own page and manual treat it as a shallow well pump for 25 ft or less to water, so use deep well equipment for anything deeper.

Common mistakes

  • Looking for electrical faults before checking whether the pump has lost prime.
  • Using a shallow well jet pump where water drops below 25 ft.
  • Running the FP4122 on 115 V without converting the motor wiring.
  • Touching the starting capacitor before it has been discharged.
  • Leaving the tank precharge unchecked when the pump cycles rapidly.

Products that fit

Questions readers ask

Are Flotec pumps any good?

They are Pentair products with full manuals, spec sheets and stated warranties: one year on the FP4122 jet, three on the FP2211 submersible and five on the E75STVT sewage pump. Pick by matching the published ratings to your well or basin.

Why is my Flotec pump not pumping water?

Pentair says to stop the pump and check prime first. Air leaks in the suction line, a leaking or plugged foot valve and a water level that has dropped below the suction pipe are the usual causes.

How do I adjust a Flotec pressure switch?

Pentair publishes separate instructions: with power off, turn the main nut to move both settings, about 2-1/2 psi per turn, and keep cut-in no lower than 20 psi and cut-off no higher than 60 psi.

Read next