First find the depth to water while pumping. Up to about 25 ft, a shallow well jet pump works; to about 90 ft, a convertible jet with a deep-well ejector; deeper, a submersible. Then read each candidate's maker table at your depth and switch pressure and make sure it meets your peak flow. Breaker and wire size come from the motor's horsepower, voltage and the cable run.
Depth to water decides the pump type
The depth that matters is the pumping water level: how far down the water stands when the pump has been running, not the depth of the well. A jet pump at the surface lifts water by suction, and atmospheric pressure caps how far that can reach. Wayne publishes its shallow well SWS pumps' output only to 25 ft of lift. Its convertible CWS pumps, fitted with a deep-well ejector in the well, carry tables from 30 to 90 ft. Beyond that, a submersible pump in the well pushes water up instead of pulling it.
Red Lion's 4-inch submersibles are meant for drilled wells of 4 in diameter or larger to depths of 250 ft, with shut-off heads from 212 ft for the 1/2 hp models to 434 ft for the 1 hp. Flotec asks for a submersible to sit at least 15 to 20 ft below the lowest pumping water level and at least 5 ft above the bottom of the well.
| Depth to water | Pump type | Example | Maker table range |
|---|---|---|---|
| Up to about 25 ft | Shallow well jet | Wayne SWS50, SWS75 | 0 to 25 ft |
| About 30 to 90 ft | Convertible jet, deep-well ejector | Wayne CWS50, CWS75 | 30 to 90 ft |
| Deeper wells | 4-inch submersible | Red Lion RL12 series | Shut-off 212 to 434 ft |
Figures: Wayne SWS shallow well jet pump manual 640002W-001 G; Wayne CWS convertible jet pump manual 640003W-001 E; Red Lion 4-inch deep well submersible pump owner's manual 106720101.
Flow at your depth and pressure
Every well pump's output falls as the water gets deeper and as the pressure setting rises. Maker tables show both at once, and that is the table to size from. Wayne's 1/2 HP SWS50, a shallow well pump, gives 711 GPH at 30 psi with water at the surface and 529 GPH at 25 ft. Its 1/2 HP CWS50 convertible gives 280 GPH at 40 psi from 30 ft, but only 62 GPH at 90 ft, where the 1 HP CWS100 still gives 129 GPH.
Size for your peak demand, the most water drawn at once, such as a shower and a washing machine together, and choose the switch setting first, because a pump that comfortably supplies 30/50 may struggle to reach a higher setting at depth. The pressure tank stretches cycles but does not add flow. For a shortlist, the shallow well jet pump list and the deep well submersible list show maker figures side by side.
| Model | 30 ft | 50 ft | 70 ft | 90 ft |
|---|---|---|---|---|
| CWS50 (1/2 HP) | 280 | 207 | 135 | 62 |
| CWS75 (3/4 HP) | 291 | 226 | 161 | 96 |
| CWS100 (1 HP) | 302 | 244 | 187 | 129 |
Figures: Wayne CWS convertible jet pump manual 640003W-001 E.
Horsepower vs depth
Horsepower buys head, the ability to push against depth and pressure. In Red Lion's 12 GPM 4-inch series, the 1/2 hp models shut off at 212 ft, the 3/4 hp at 333 ft and the 1 hp at 434 ft. The pump must reach your required head with margin: depth to water, plus the height from the wellhead to the tank, plus the switch cut-out pressure expressed as feet of water, plus friction. Picking a pump whose shut-off is barely above that total means very little flow at the top of the pressure range.
More horsepower at shallow depth is not better. Wayne's tables show the 1 HP CWS100 barely out-producing the 1/2 HP CWS50 at 30 ft; the extra power only pays off deeper. Red Lion's convertible jet advice warns that a pump with more capacity than the well can supply will run hot and fail to shut off, so the well's recovery rate caps the useful size. The shallow vs deep well guide covers the choice of pump style.
Well pump breaker size
Breaker size comes from the motor, and makers publish it. Flotec's manual for its 4-inch G-series motors gives fuse and breaker sizes for each horsepower and voltage, shown below. Use the table for your own motor's maker; values differ between 2-wire and 3-wire motors even at the same horsepower, and other makers' motors may differ again. Red Lion's instruction is to fit a fused disconnect or circuit breaker matched to the motor and control box ratings, and to have the work done by a licensed electrician.
Jet pumps above ground are usually dual-voltage. Wayne's SWS and CWS pumps run on 120 or 230 V, and the 230 V setting halves the current, which often allows a smaller wire.
| Motor | Voltage | Circuit breaker |
|---|---|---|
| 1/2 HP 2-wire | 115 V | 25 A |
| 1/2 HP 2-wire | 230 V | 10 A |
| 3/4 HP 2-wire | 230 V | 15 A |
| 1 HP 2-wire | 230 V | 20 A |
| 1/2 HP 3-wire | 230 V | 15 A |
| 3/4 HP 3-wire | 230 V | 20 A |
| 1 HP 3-wire | 230 V | 25 A |
Figures: Flotec 4-inch submersible pumps installation and operation manual FP874.
Wire size and cable length
A submersible's cable runs from the service panel all the way down the well, and voltage drop over that length is a real limit. Flotec lists the maximum copper cable length for each wire gauge. With 12 AWG copper at 230 V, its 2-wire tables allow about 697 ft for 1/2 HP, 581 ft for 3/4 HP and 484 ft for 1 HP; its 3-wire tables allow 553, 425 and 323 ft. Longer runs need heavier wire, and Flotec says aluminum cable must go up two sizes.
Low voltage at the motor is one of the most common causes of overload trips and weak pressure in Red Lion's troubleshooting guide, so do not trim the wire size to save money. Measure the run from the panel to the pump, not just the well depth.
| Motor | 2-wire | 3-wire |
|---|---|---|
| 1/2 HP | 697 ft | 553 ft |
| 3/4 HP | 581 ft | 425 ft |
| 1 HP | 484 ft | 323 ft |
Figures: Flotec 4-inch submersible pumps installation and operation manual FP874.
Putting it together
With the depth, pressure and flow settled, the choice is usually narrow. For a shallow well under about 25 ft, a pump like the Wayne SWS50 is the simplest system. For a 4 in well with deeper water, a submersible like the Red Lion RL12G05-2W2V avoids priming altogether. Then size the pressure tank for at least a minute of run time; the pressure tank guide shows how.
- Measure the pumping water level, not just the well depth.
- Choose the switch setting you want at the taps.
- Estimate peak flow in gallons per minute or per hour.
- Read maker tables at your depth and pressure.
- Take breaker and wire size from the motor maker's tables.
Common mistakes
- Sizing from the well depth instead of the pumping water level.
- Reading a pump's flow at zero depth or the lowest pressure only.
- Choosing a pump that out-pumps the well's recovery rate.
- Using wire sized for the well depth rather than the full cable run.
- Copying breaker sizes from a different maker's motor table.
Products that fit

Wayne SWS50 Shallow Well Jet Pump
1/2 HP shallow well jet pump rated to 25 ft of lift in Wayne's table.

Wayne CWS50 Convertible Jet Well Pump
1/2 HP convertible jet with output listed from 30 to 90 ft.

Red Lion RL12G05-2W2V 2-Wire Deep Well Pump
1/2 hp 2-wire 4-inch submersible with a 212 ft shut-off head.

Red Lion RL12G07-2W2V 2-Wire Submersible Well Pump
3/4 hp 2-wire submersible reaching 333 ft of shut-off head.
Questions readers ask
What size breaker do I need for a well pump?
It depends on the motor's horsepower, voltage and wiring style. Flotec's G-series table, for example, lists 20 A for a 1 HP 2-wire motor at 230 V and 25 A for a 1 HP 3-wire motor. Use the table from your own motor's maker.
What horsepower well pump do I need for a deep well?
It depends on the pumping water level, not the well depth, plus the pressure you want. Red Lion's 1/2 hp 12 GPM submersible shuts off at 212 ft of head, so it leaves little margin once the total head approaches that; its 3/4 hp model, at 333 ft, gives far more room.
How deep can a shallow well pump draw water?
Wayne lists its SWS shallow well pumps up to 25 ft of lift. Below that, use a convertible jet with a deep-well ejector, which Wayne tables to 90 ft, or a submersible.
Is a bigger well pump better?
Not if the well cannot keep up. Red Lion warns that a pump that out-pumps the well runs hot and won't shut off. Size for peak demand at your depth and pressure, with a little margin.